DIGLYCIDYL ETHER OF BISPHENOL A
| CAS # | 1675-54-3 |
|---|---|
| Formula |
C₂₁H₂₄O₄ |
| Synonyms |
bisphenol A diglycidyl ether; 2,2-bis(p-2,3-epoxypropoxy) phenyl)propane; 4,4'-isopropylidenediphenol diglycidyl ether; composite constituent |
| Physical description | Odorless yellowish brown liquid. | ||
|---|---|---|---|
| Boiling point | decomposes | Molecular weight | 312.37 |
| Freezing point/melting point | 46-54°F | Vapor pressure | |
| Flash point | >200°F | Vapor density | |
| Specific gravity | 1.16 | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | D709 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | GFF (37 mm), Type A/E [AP4003705] |
| Sampling time* | 240 min |
| Sampling volume (TWA)* | 240 L |
| Sampling flow rate (TWA)* | 1 L/min |
| Sampling volume (STEL/Peak/C)* | |
| Sampling flow rate (STEL/Peak/C)* | |
| Analytical method instruments | HPLC |
| Method reference | OSHA 1018 (fully validated) |
| Notes | |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA | REL-TWA | TLV-TWA | PEL-TWA | ||||
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
NA |
Skin notation |
NA |
Skin notation |
NA |
Skin notation |
NA |
|
Notes:
Not established |
Notes:
Not established |
Notes:
Not established |
Notes:
Not established |
||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Bisphenol a diglycidyl ether NIOSH: Pocket Guide to Chemical Hazards - Bisphenol a diglycidyl ether Literature References |
Last Updated Date : 12/28/2020
PERFLUOROISOBUTYLENE
| CAS # | 382-21-8 |
|---|---|
| Formula |
C₄F₈ |
| Synonyms |
octafluoroisobutene; PFIB; octafluoro-sec-butene; 1,1,3,3,3-Pentafluoro-2-trifluoromethyl-1-propene |
| Physical description | Colorless, odorless gas at room temp. When heated to decomposition it emits toxic fumes of hydrogen fluoride. | ||
|---|---|---|---|
| Boiling point | 44.6°F | Molecular weight | 200.03 |
| Freezing point/melting point | -202°F | Vapor pressure | 1740 mmHg |
| Flash point | Vapor density | 6.3 | |
| Specific gravity | 1.592 | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | |||
|---|---|---|---|
| Sampling group | |||
| Sampler/Sampling media | |||
| Sampling time* | |||
| Sampling volume (TWA)* | |||
| Sampling flow rate (TWA)* | |||
| Sampling volume (STEL/Peak/C)* | |||
| Sampling flow rate (STEL/Peak/C)* | |||
| Analytical method instruments | |||
| Method reference | |||
| Notes | |||
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media |
|
|---|---|
| Bulk Method |
|
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA |
|
REL-TWA |
|
TLV-TWA |
|
PEL-TWA |
|
| PEL-STEL |
|
REL-STEL |
|
TLV-STEL |
|
PEL-STEL |
|
| PEL-C |
|
REL-C |
|
TLV-C |
0.01 ppm [1989] |
PEL-C |
0.01 ppm (0.082 mg/m³) |
| Skin notation |
NA |
Skin notation |
NA |
Skin notation |
N |
Skin notation |
N |
|
Notes:
Not established |
Notes:
Not established |
Notes:
|
Notes:
|
||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: |
Notes:
|
||||||
|
AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3:
--/0.1 ppm/0.3 ppm |
|||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Not listed NIOSH: Pocket Guide to Chemical Hazards - Not listed Literature References
|
Last Updated Date : 01/08/2021
TETRAETHYL DITHIOPYROPHOSPHATE (TEDP)†
| CAS # | 3689-24-5 |
|---|---|
| Formula |
C₈H₂₀O₅P₂S₂ |
| Synonyms |
Bladafum; Dithion; Sulfotep; tetraethyl dithionopyrophosphate; tetraethyl dithiopyrophosphate; Thiotepp; TEDP |
| Physical description | Pale-yellow liquid with a garlic-like odor. | ||
|---|---|---|---|
| Boiling point | 277-282°F at 2 mmHg | Molecular weight | 322.32 |
| Freezing point/melting point | Vapor pressure | 0.0002 mmHg | |
| Flash point | Vapor density | ||
| Specific gravity | 1.196 (at 77°F) | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | |||
|---|---|---|---|
| Sampling group | |||
| Sampler/Sampling media | |||
| Sampling time* | |||
| Sampling volume (TWA)* | |||
| Sampling flow rate (TWA)* | |||
| Sampling volume (STEL/Peak/C)* | |||
| Sampling flow rate (STEL/Peak/C)* | |||
| Analytical method instruments | |||
| Method reference | |||
| Notes | |||
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA |
0.2 mg/m³ |
REL-TWA |
0.2 mg/m³ |
TLV-TWA |
0.1 mg/m³ (inhalable fraction and vapor) [1993] |
PEL-TWA |
0.2 mg/m³ |
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
Y |
Skin notation |
Y |
Skin notation |
Y |
Skin notation |
Y |
| Notes: | Notes: |
Notes:
BEI® |
Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH |
10 mg/m³ |
|||||
| Carcinogenic classifications: TLV-A4 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Tetraethyl dithiopyrophosphate NIOSH: Pocket Guide to Chemical Hazards - TEDP Literature References
|
Last Updated Date : 01/28/2021
SULPROFOS
| CAS # | 35400-43-2 |
|---|---|
| Formula |
C₁₂H₁₉O₂PS₃ |
| Synonyms |
Bolstar; O-ethyl O-(4-methylthio)phenyl S-propylphosphorodithioate |
| Physical description | Tan-colored liquid with a sulfide-like odor. | ||
|---|---|---|---|
| Boiling point | Molecular weight | 322.5 | |
| Freezing point/melting point | Vapor pressure | <8 mmHg | |
| Flash point | Vapor density | ||
| Specific gravity | 1.20 | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | S129 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | OSHA versatile sampler (OVS-2) - 13 mm XAD-2 tube (270/140 mg) with GFF enclosed [SKC 226-30-16] |
| Sampling time* | |
| Sampling volume (TWA)* | 480 L |
| Sampling flow rate (TWA)* | 1 L/min |
| Sampling volume (STEL/Peak/C)* | |
| Sampling flow rate (STEL/Peak/C)* | |
| Analytical method instruments | GC-FPD |
| Method reference | OSHA PV2037 (partially validated) |
| Notes | |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA | REL-TWA |
1 mg/m³ |
TLV-TWA |
0.1 mg/m³ (inhalable fraction and vapor) [2008] |
PEL-TWA |
1 mg/m³ |
|
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
NA |
Skin notation |
N |
Skin notation |
Y |
Skin notation |
N |
|
Notes:
Not established |
Notes: |
Notes:
BEI® |
Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: TLV-A4 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Sulprofos NIOSH: Pocket Guide to Chemical Hazards - Sulprofos Literature References
|
Last Updated Date : 01/12/2021
CARBONYL FLUORIDE
| CAS # | 353-50-4 |
|---|---|
| Formula |
CF₂O |
| Synonyms |
carbon difluoride oxide; carbon fluoride oxide; carbon oxyfluoride; carbonyl difluoride; fluoroformyl fluoride; fluorophosgene |
| Physical description | Colorless gas with a pungent and very irritating odor. | ||
|---|---|---|---|
| Boiling point | -118°F | Molecular weight | 66.01 |
| Freezing point/melting point | -173°F | Vapor pressure | 55.4 atm |
| Flash point | Vapor density | 1.139 at -173.2°F | |
| Specific gravity | Ionization potential | 13.02 eV | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | 4 | NFPA fire rating | 0 |
| NFPA reactivity rating | 0 | NFPA special instruction | |
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | C105 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | Mixed cellulose ester filter (MCEF) 0.8 micron (37 mm) and filter spacer with Na₂CO₃ impregnated backup pad, in a 3-piece cassette [SKC 225-9001] |
| Sampling time* | 60 min |
| Sampling volume (TWA)* | 90 L |
| Sampling flow rate (TWA)* | 1.5 L/min |
| Sampling volume (STEL/Peak/C)* | 22.5 L |
| Sampling flow rate (STEL/Peak/C)* | 1.5 L/min |
| Analytical method instruments | ISE |
| Method reference | OSHA ID-110 (fully validated) |
| Notes | Submit as a separate sample (Particulate F- on MCEF, carbonyl fluoride on impregnated backup pad). The filter and filter spacer reside in one section while the impregnated backup pad is in another section of a 3-piece polystyrene cassette. The filter and backup pad should not have physical contact with one another. When analysis of a compound is requested, an analysis is performed for fluoride (F-) and reported as the compound. Carbonyl fluoride gas is collected on a Na₂CO₃ impregnated backup pad. |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA | REL-TWA |
2 ppm (5 mg/m³) |
TLV-TWA |
2 ppm [1990] |
PEL-TWA |
2 ppm (5 mg/m³) |
|
| PEL-STEL | REL-STEL |
5 ppm (15 mg/m³) |
TLV-STEL |
5 ppm [1990] |
PEL-STEL |
5 ppm (15 mg/m³) |
|
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
NA |
Skin notation |
N |
Skin notation |
N |
Skin notation |
N |
|
Notes:
Not established |
Notes: | Notes: | Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: Not listed | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Carbonyl fluoride NIOSH: Pocket Guide to Chemical Hazards - Carbonyl fluoride Literature References
|
Last Updated Date : 11/02/2023
DIPROPYLENE GLYCOL METHYL ETHER ((2-METHOXYMETHYLETHOXY)PROPANOL)†
| CAS # | 34590-94-8 |
|---|---|
| Formula |
C₇H₁₆O₃ |
| Synonyms |
dipropylene glycol monomethyl ether; (2-methoxymethylethoxy)propanol; bis-(2-methoxypropyl) ether |
| Physical description | Colorless liquid with a mild, ether-like odor. | ||
|---|---|---|---|
| Boiling point | 408°F | Molecular weight | 148.2 |
| Freezing point/melting point | -112°F | Vapor pressure | 0.5 mmHg |
| Flash point | 166°F | Vapor density | 5.11 |
| Specific gravity | 0.95 | Ionization potential | |
| Lower explosive limit (LEL) | 1.1% at 392°F | Upper explosive limit (UEL) | 3% |
| NFPA health rating | 2 | NFPA fire rating | 2 |
| NFPA reactivity rating | 0 | NFPA special instruction | |
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | 1014 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | CSC tube (100/50 mg) [SKC 226-01] |
| Sampling time* | 100 min |
| Sampling volume (TWA)* | 10 L |
| Sampling flow rate (TWA)* | 0.1 L/min |
| Sampling volume (STEL/Peak/C)* | |
| Sampling flow rate (STEL/Peak/C)* | |
| Analytical method instruments | GC-FID |
| Method reference | OSHA 101 (fully validated) |
| Notes | |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA |
100 ppm (600 mg/m³) |
REL-TWA |
100 ppm (600 mg/m³) |
TLV-TWA |
50 ppm [2021] |
PEL-TWA |
100 ppm (600 mg/m³) |
| PEL-STEL | REL-STEL |
150 ppm (900 mg/m³) |
TLV-STEL | PEL-STEL |
150 ppm (900 mg/m³) |
||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
Y |
Skin notation |
Y |
Skin notation |
Y |
Skin notation |
Y |
| Notes: | Notes: | Notes: | Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH |
600 ppm |
|||||
| Carcinogenic classifications: Not listed | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Dipropylene glycol methyl ether NIOSH: Pocket Guide to Chemical Hazards - Dipropylene glycol methyl ether Literature References
|
Last Updated Date : 12/28/2020
TEMEPHOS (ABATE)†
| CAS # | 3383-96-8 |
|---|---|
| Formula |
C₁₆H₁₂O₆P₂S₃ |
| Synonyms |
Abate; O,O,O'O'-tetramethyl O,O'-thiodi-p-phenylene phosphorothioate; phosphorothioic acid, O,O-dimethyl ester, O,O-diester with 4,4'-thiodiphenol |
| Physical description | White, crystalline solid or liquid (above 87°F). | ||
|---|---|---|---|
| Boiling point | 248-257°F (decomposes) | Molecular weight | 466.5 |
| Freezing point/melting point | 87°F | Vapor pressure | 0.00000007 mmHg at 77°F |
| Flash point | Vapor density | ||
| Specific gravity | 1.32 | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | 0005 (total); request using analyte code 9135 | T195 (resp); request using analyte code 9130 |
|---|---|---|
| Sampling group | ||
| Sampler/Sampling media | Tared low-ash 37 mm PVC filter, 5 microns [SLTC108] | Tared low-ash 37 mm PVC filter, 5 microns, preceded by 10 mm nylon Dorr-Oliver cyclone for respirable samples. [SLTC108] |
| Sampling time* | 240-480 min |
240-480 min |
| Sampling volume (TWA)* | 960 L |
816 L |
| Sampling flow rate (TWA)* | 2 L/min |
1.7 L/min ±5% |
| Sampling volume (STEL/Peak/C)* | ||
| Sampling flow rate (STEL/Peak/C)* | ||
| Analytical method instruments | Gravimetric | Gravimetric |
| Method reference | OSHA PV2121 (partially validated) | OSHA PV2121 (partially validated) |
| Notes | If the net weight of the sample yields a concentration below the PEL after considering the associated SAE , the SLTC will perform no further work on the sample and the sample air concentration will be reported as the calculated gravimetric air concentration. If the net weight corresponds to an amount greater than the PEL value after considering the associated SAE, the sample may be analyzed for the applicable component and appropriate results will be reported. |
If the filter is not overloaded, samples can be collected up to an 8-hour period. If the net weight of the sample yields a concentration below the PEL after considering the associated SAE , the SLTC will perform no further work on the sample and the sample air concentration will be reported as the calculated gravimetric air concentration. If the net weight corresponds to an amount greater than the PEL value after considering the associated SAE, the sample may be analyzed for the applicable component and appropriate results will be reported. |
| Special requirements | FOR TOTAL DUST SAMPLES, DO NOT USE A CYCLONE!! |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | Wipe with GFF (37 mm), Type A/E [AP4003705] |
|---|---|
| Bulk Method | Limit the amount of bulk submitted to 1 g or 1 mL. |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA |
15 mg/m³ (total dust), 5 mg/m³ (respirable fraction) |
REL-TWA |
10 mg/m³ (total), 5 mg/m³ (resp) |
TLV-TWA |
1 mg/m³ (inhalable particulate matter) [2002] |
PEL-TWA |
10 mg/m³ (total dust), 5 mg/m³ (respirable fraction) |
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
N |
Skin notation |
N |
Skin notation |
Y |
Skin notation |
N |
| Notes: | Notes: |
Notes:
BEI® |
Notes:
See footnote [n]. |
||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: TLV-A4 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Temephos NIOSH: Pocket Guide to Chemical Hazards - Temephos Literature References
|
Last Updated Date : 01/12/2021
DIAZOMETHANE†
| CAS # | 334-88-3 |
|---|---|
| Formula |
CH₂N₂ |
| Synonyms |
azimethylene; azomethylene; diazirine |
| Physical description | Yellow gas with a musty odor. | ||
|---|---|---|---|
| Boiling point | -9°F | Molecular weight | 42.1 |
| Freezing point/melting point | -229°F | Vapor pressure | >1 atm |
| Flash point | Vapor density | 1.45 | |
| Specific gravity | Ionization potential | 9.00 eV | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | 0861 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | XAD-2 tube (100/50 mg) coated with octanoic acid [SKC 226-23] |
| Sampling time* | |
| Sampling volume (TWA)* | 6-30 L |
| Sampling flow rate (TWA)* | 0.2 L/min |
| Sampling volume (STEL/Peak/C)* | |
| Sampling flow rate (STEL/Peak/C)* | |
| Analytical method instruments | GC-FID |
| Method reference | NIOSH 2515 (partially validated) |
| Notes | |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA |
0.2 ppm (0.4 mg/m³) |
REL-TWA |
0.2 ppm (0.4 mg/m³) |
TLV-TWA |
0.2 ppm [1970] |
PEL-TWA |
0.2 ppm (0.4 mg/m³) |
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
N |
Skin notation |
N |
Skin notation |
N |
Skin notation |
N |
| Notes: | Notes: | Notes: | Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH |
2 ppm |
|||||
| Carcinogenic classifications: IARC-3, TLV-A2 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Diazomethane NIOSH: Pocket Guide to Chemical Hazards - Diazomethane Literature References
|
Last Updated Date : 12/22/2020
DIAZINON®
| CAS # | 333-41-5 |
|---|---|
| Formula |
C₁₂H₂₁N₂O₃PS |
| Synonyms |
Basudin; diazide; o,o-diethyl-o-2-isopropyl-4-methyl-6-pyrimidinyl-phosphorothioate; Spectracide |
| Physical description | Colorless liquid with a faint ester-like odor. | ||
|---|---|---|---|
| Boiling point | decomposes | Molecular weight | 304.4 |
| Freezing point/melting point | Vapor pressure | 0.0001 mmHg | |
| Flash point | 180°F | Vapor density | |
| Specific gravity | 1.12 | Ionization potential | |
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | 2720 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | OSHA versatile sampler (OVS-2) - 13 mm XAD-2 tube (270/140 mg) with GFF enclosed [SKC 226-30-16] |
| Sampling time* | 480 min |
| Sampling volume (TWA)* | 480 L |
| Sampling flow rate (TWA)* | 1 L/min |
| Sampling volume (STEL/Peak/C)* | 15 L |
| Sampling flow rate (STEL/Peak/C)* | 1 L/min |
| Analytical method instruments | GC-FPD |
| Method reference | OSHA 62 (fully validated) |
| Notes | |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA | REL-TWA |
0.1 mg/m³ |
TLV-TWA |
0.01 mg/m³ (inhalable fraction and vapor) [2000] |
PEL-TWA |
0.1 mg/m³ |
|
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
NA |
Skin notation |
Y |
Skin notation |
Y |
Skin notation |
Y |
|
Notes:
Not established |
Notes: |
Notes:
BEI® |
Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: TLV-A4 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Diazinon NIOSH: Pocket Guide to Chemical Hazards - Diazinon® Literature References
|
Last Updated Date : 12/22/2020
DIURON
| CAS # | 330-54-1 |
|---|---|
| Formula |
C₉H₁₀Cl₂N₂O |
| Synonyms |
3-(3,4-dichlorophenyl)-1,1-dimethylurea; Direx®; Karmex® |
| Physical description | White, odorless, crystalline solid. | ||
|---|---|---|---|
| Boiling point | 356°F (decomposes) | Molecular weight | 233.1 |
| Freezing point/melting point | 316°F | Vapor pressure | 0.000000002 mmHg |
| Flash point | Vapor density | ||
| Specific gravity | Ionization potential | ||
| Lower explosive limit (LEL) | Upper explosive limit (UEL) | ||
| NFPA health rating | NFPA fire rating | ||
| NFPA reactivity rating | NFPA special instruction | ||
| Vapor hazard ratio (VHR) | |||
| Historical exceedance percentage | |||
| Target organs | |||
| Analyte code (IMIS no.) | 2684 |
|---|---|
| Sampling group | |
| Sampler/Sampling media | OSHA versatile sampler (OVS-2) - 13 mm XAD-2 tube (270/140 mg) with GFF enclosed [SKC 226-30-16] |
| Sampling time* | |
| Sampling volume (TWA)* | 60 L |
| Sampling flow rate (TWA)* | 1 L/min |
| Sampling volume (STEL/Peak/C)* | |
| Sampling flow rate (STEL/Peak/C)* | |
| Analytical method instruments | HPLC-UV |
| Method reference | OSHA PV2097 (partially validated) |
| Notes | Protect the samples from light. |
| Special requirements |
* All sampling instructions above are recommended guidelines for OSHA Compliance Safety and Health Officers (CSHOs), please see the corresponding OSHA method reference for complete details.
| Wipe Sampler/Sampling media | |
|---|---|
| Bulk Method |
| Device | |||||
|---|---|---|---|---|---|
| Model/Type | |||||
|
Sampling information (see manufacturer instructions) |
|
OSHA PEL
8-hour TWA (ST) STEL (C) Ceiling Peak |
NIOSH REL
Up to 10-hour TWA (ST) STEL (C) Ceiling |
ACGIH TLV©
8-hour TWA (ST) STEL (C) Ceiling |
|||||
|---|---|---|---|---|---|---|---|
| PEL-TWA | REL-TWA |
10 mg/m³ |
TLV-TWA |
10 mg/m³ [1974] |
PEL-TWA |
10 mg/m³ |
|
| PEL-STEL | REL-STEL | TLV-STEL | PEL-STEL | ||||
| PEL-C | REL-C | TLV-C | PEL-C | ||||
| Skin notation |
NA |
Skin notation |
N |
Skin notation |
N |
Skin notation |
N |
|
Notes:
Not established |
Notes: | Notes: | Notes: | ||||
| Health factors: See NIH-NLM PubChem. | IDLH | ||||||
| Carcinogenic classifications: TLV-A4 | Notes: | ||||||
| AIHA emergency response planning guidelines - ERPG-1/ERPG-2/ERPG-3: | |||||||
Additional Resources and Literature References
|
NOAA: CAMEO Chemicals - Diuron NIOSH: Pocket Guide to Chemical Hazards - Diuron Literature References
|
Last Updated Date : 12/28/2020